BS EN 14382-2005+A1-2009
氣壓調節站和裝置用安全設備.進氣口壓力達100 帕的氣體安全截止裝置

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

BS EN 14382-2005+A1-2009 發布歷史

This document specifies constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations in accordance with EN 12186 or EN 12279: - for inlet pressures up to 100 bar and nominal diameters up to DN 400; - for an operating temperature range from –20 °C to +60 °C, which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations. "Gas safety shut-off devices" will hereafter be called "SSDs" except in titles. For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Requirements except the external corrosion resistance in case of environmental conditions where corrosion is likely to occur." This document considers the following classes/types of SSDs: temperature classes: - class 1: operating temperature range from –10 °C to 60 °C; - class 2: operating temperature range from –20 °C to 60 °C; functional classes: -class A: SSDs that close when damage to the pressure detector element occurs (applicable to overpressure SSDs only) or when external power fails and whose re-opening, after an intervention for overpressure, is possible only manually; - class B: SSDs that do not close when damage to the pressure detector element occurs and whose reopening, after an intervention for overpressure, is possible only manually; SSDs types: - type IS: (integral strength type); - type DS: (differential strength type). SSDs complying with the requirements of this document may be declared as “in conformity with EN 14382“ and bear the mark “EN 14382”. The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document. This document does not apply to: - SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters; - SSDs incorporated into pressure-regulating devices used in service lines with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.

BS EN 14382-2005+A1-2009由英國標準學會 GB-BSI 發布于 2006-02-23，并于 2006-02-23 實施。

BS EN 14382-2005+A1-2009 在中國標準分類中歸屬于: J16 閥門，在國際標準分類中歸屬于: 23.060.40 壓力調節器。

BS EN 14382-2005+A1-2009 發布之時，引用了標準

• EN 473-2000 *， 2022-07-23 更新
• EN 287-1-1992 熔焊用焊機的合格試驗.第1部分:鋼
• EN 334-2005 入口壓力100巴及以下用氣體壓力調節器.包含修改件A1-2009
• EN 970-1997 焊縫無損檢測.外觀檢測
• EN 1092-1-2007 法蘭及其連接件.按PN標注的管,閥門,配件和附件用圓形法蘭.第1部分:鋼法蘭*， 2007-08-01 更新
• EN 1759-1 法蘭及其連接件.等級標示的管,閥門,配件和附件用環形法蘭.第1部分:NPS 1/2到24 鋼法蘭*， 2022-07-23 更新
• EN 10226-1 有壓力緊固連接件的管道螺紋.第1部分:錐形外螺紋和平行內螺紋.尺寸,公差和名稱與符號
• EN 10226-2 螺紋上壓力強密聯接的管螺紋.第2部分:錐形外螺紋和錐形內螺紋.尺寸,公差及名稱和符號
• EN 12186 天然氣基礎設施.氣體壓力調節站的傳輸和分配功能要求*， 2014-10-01 更新
• EN 12279 燃氣供應系統.作業線上的氣壓調節裝置.功能要求.包含修改件A1:07/2005
• EN 12516-1-2005 工業閥門.外殼設計強度.第1部分:鋼制閥門外殼的列表法
• EN 12516-2-2004 閥門.外殼設計強度.第2部分:鋼制閥門外殼的計算方法
• EN 12516-4-2008 工業閥門.外殼設計強度.第4部分:金屬材料制造的(除了鋼制的)閥門外殼用計算方法*， 2008-01-01 更新
• EN 12627 *， 2017-11-01 更新
• EN 13445-4 不燃燒的壓力容器.第4部分:建造*， 2014-09-01 更新
• EN 13906-1 *， 2013-07-01 更新
• EN 13906-2 圓形金屬絲和棒材制圓柱形螺旋彈簧.計算和設計.第2部分:拉伸彈簧*， 2013-06-01 更新
• EN 60534-1-1993 
• EN ISO 175-2000 塑料.浸入液體化學制品的影響測定的試驗方法
• EN ISO 9606-2-2004 焊工的認可試驗.熔焊.鋁和鋁合金 ISO 9606-2-2004;代替EN 287-2-1992*， 2022-07-23 更新

* 在 BS EN 14382-2005+A1-2009 發布之后有更新，請注意新發布標準的變化。

BS EN 14382-2005+A1-2009的歷代版本如下：

• 2006年02月23日 BS EN 14382-2005+A1-2009 氣壓調節站和裝置用安全設備.進氣口壓力達100 帕的氣體安全截止裝置

BS EN 14382-2005+A1-2009 帶上方澆口的通電閥門 由 BS EN 14382-2005 變更而來。

BS EN 14382-2005+A1-2009 帶上方澆口的通電閥門 由 BS EN 14382-2002 變更而來。

非常抱歉，我們暫時無法提供預覽，您可以試試： 免費下載 BS EN 14382-2005+A1-2009 前三頁，或者稍后再訪問。

注意： 點擊下載后，生成下載文件時間比較長，請耐心等待......

標準號

BS EN 14382-2005+A1-2009

發布日期

2006年02月23日

實施日期

2006年02月23日

廢止日期

無

中國標準分類號

J16

國際標準分類號

23.060.40

發布單位

GB-BSI

引用標準

EN 473-2000 EN 287-1-1992 EN 334-2005 EN 970-1997 EN 1092-1-2007 EN 1759-1 EN 10226-1 EN 10226-2 EN 12186 EN 12279 EN 12516-1-2005 EN 12516-2-2004 EN 12516-4-2008 EN 12627 EN 13445-4 EN 13906-1 EN 13906-2 EN 60534-1-1993 EN ISO 175-2000 EN ISO 9606-2-2004

被代替標準

BS EN 14382-2005 04/30117506 DC-2004 BS EN 14382-2002

適用范圍

This document specifies constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations in accordance with EN 12186 or EN 12279: - for inlet pressures up to 100 bar and nominal diameters up to DN 400; - for an operating temperature range from –20 °C to +60 °C, which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations. "Gas safety shut-off devices" will hereafter be called "SSDs" except in titles. For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Requirements except the external corrosion resistance in case of environmental conditions where corrosion is likely to occur." This document considers the following classes/types of SSDs: temperature classes: - class 1: operating temperature range from –10 °C to 60 °C; - class 2: operating temperature range from –20 °C to 60 °C; functional classes: -class A: SSDs that close when damage to the pressure detector element occurs (applicable to overpressure SSDs only) or when external power fails and whose re-opening, after an intervention for overpressure, is possible only manually; - class B: SSDs that do not close when damage to the pressure detector element occurs and whose reopening, after an intervention for overpressure, is possible only manually; SSDs types: - type IS: (integral strength type); - type DS: (differential strength type). SSDs complying with the requirements of this document may be declared as “in conformity with EN 14382“ and bear the mark “EN 14382”. The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document. This document does not apply to: - SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters; - SSDs incorporated into pressure-regulating devices used in service lines with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.

BS EN 14382-2005+A1-2009 中可能用到的儀器設備