ASTM D6117-23
塑料木材和型材機械緊固件的標準試驗方法

Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes

ASTM D6117-23 發布歷史

ASTM D6117-23由美國材料與試驗協會 US-ASTM 發布于 2023-07-01。

ASTM D6117-23在國際標準分類中歸屬于: 83.140.01 橡膠和塑料制品綜合。

ASTM D6117-23 塑料木材和型材機械緊固件的標準試驗方法的最新版本是哪一版？

最新版本是 ASTM D6117-23 。

ASTM D6117-23 發布之時，引用了標準

• ASTM D1761 機械緊固件在木制品中的標準試驗方法
• ASTM D6111 通過代替對塑料層材和形材特殊重量和體密度的標準試驗方法
• ASTM D6341 測定-30到140°F(-34.4到60℃)之間塑料制材和型材線熱膨脹系數的標準試驗方法
• ASTM D883 塑料相關標準術語*， 2024-02-01 更新
• ASTM E4 試驗機的負荷校準的標準實施規程

* 在 ASTM D6117-23 發布之后有更新，請注意新發布標準的變化。

ASTM D6117-23的歷代版本如下：

• 2023年 ASTM D6117-23 塑料木材和型材機械緊固件的標準試驗方法
• 2018年 ASTM D6117-18 塑料木材和型材機械緊固件的標準試驗方法
• 2016年 ASTM D6117-16 塑料木材和型材的機械緊固件的標準試驗方法
• 2013年 ASTM D6117-13e1 塑料成材和形材內機械緊固件的標準試驗方法
• 2013年 ASTM D6117-13 塑料制材和型材中機械緊固件的標準試驗方法
• 2010年 ASTM D6117-10 塑料板材和型材中使用的機械緊固件的標準試驗方法
• 1997年 ASTM D6117-97(2005) 塑料成材和形材內機械緊固件的標準試驗方法
• 1997年 ASTM D6117-97 塑料成材和形材內機械緊固件的標準試驗方法

1.1 These test methods cover the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures. 1.2 The test methods appear in the following order: Sections Test Method A—Nail, Staple, or Screw Withdrawal Test 4 to 13 Test Method B—Nail, Staple, or Screw Lateral Resistance Test 14 to 22 1.3 Plastic lumber and plastic shapes are currently made predominately from recycled plastics. However, these test methods would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogeneous in the cross-section. 1.4 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

標準號

ASTM D6117-23

發布

2023年

發布單位

美國材料與試驗協會

當前最新

ASTM D6117-23

 

 

引用標準

ASTM D1761 ASTM D6111 ASTM D6341 ASTM D883 ASTM E4

ASTM D6117-23相似標準

推薦

誰引用了ASTM D6117-23 更多引用