ISO 11299-2:2018
地下鋪設送氣管道維修用塑料管道系統. 第2部分: 連續管道襯里
Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes
- 標準號
- ISO 11299-2:2018
- 發布
- 2018年
- 發布單位
- 國際標準化組織
- 當前最新
- ISO 11299-2:2018
- 引用標準
- EN 1555-1:2010 EN 1555-2:2010 EN 1555-3+A1:2012 EN 1555-5:2010 ISO 11299-1:2018 ISO 12176-1:2017 ISO 12176-2:2008 ISO 4437-1:2014 ISO 4437-2:2014 ISO 4437-3:2014 ISO 4437-5:2014
- 適用范圍
- This document, read in conjunction with ISO 11299-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; — Coated PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as described in Annex A. In addition it covers: — jointing of pipe lengths by means of butt fusion; — fabricated and injection-moulded fittings made of PE; It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.
ISO 11299-2:2018相似標準
推薦
淺談影響城市供水水質的因素及措施
2、更新或改造供水管道系統,深化管網管理。 ...
電磁流量計的選擇與安裝注意要點
2、由于工藝配管內流速偏低時而達不到“1”中對應通徑下的小上限流量值時，可選擇變送器通徑小于工藝配管的通徑，即在變送器前后加接異徑管。 十一、安裝形式的選擇 1、整體式：即將流量計的傳感部分和轉換部分裝于一體，優點是便于安裝。 2、分離式：即將流量計的傳感部分安裝于被測管道上，將轉換部分安裝于便于操作的室內。適用于現場環境差的場合（但其分離長度應小于30m）。 ...
電磁流量汁的正確選擇和正確使用
1.4 關于接地環的選用 電磁流量計的工作，要求被測介質必須是地電位，一般是通過管道或管道法蘭接地，若連接傳感器的工藝管道相對被測介質是絕緣的（塑料管道或有絕緣襯里的管道），就必須選用接地環或帶接地電極的傳感器，使被測介質處于地電位。 接地環的形式又分普通型和保護型，一般使用普通型，若被測介質是磨損性的，宜使用帶頸的保護接地環，以保護進出口端的襯里，延長使用壽命。...