DIN EN 16905-1-2017
燃氣式吸熱發動機驅動熱泵.第1部分:術語和定義;德文版本EN 16905-1-2017

Gas-fired endothermic engine driven heat pumps - Part 1: Terms and definitions; German version EN 16905-1:2017

DIN EN 16905-1-2017 發布歷史

This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This standard only applies to appliances having: - gas fired endothermic engines under the control of fully automatic control systems; - closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; - where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 during normal operation; - where the maximum operating pressure in the - heating water circuit (if installed) does not exceed 6 bar - domestic hot water circuit (if installed) does not exceed 10 bar. This standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this standard. Packaged units, single split and multisplit systems are covered by this standard. Single duct and double duct units are covered by this standard. The above appliances can have one or more primary or secondary functions. This standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested wo

DIN EN 16905-1-2017由德國標準化學會 DE-DIN 發布于 2017-09-00。

DIN EN 16905-1-2017 在中國標準分類中歸屬于: J75 換熱設備，在國際標準分類中歸屬于: 01.040.27 能源和熱傳導工程 (詞匯),27.080 熱泵。

DIN EN 16905-1-2017 發布之時，引用了標準

• EN 161-2011 自動切斷閥氣體燃燒器和燃氣用具
• EN 437-2003 試驗氣體.試驗壓力.器具分類.包含修改件A1-2009
• EN 12309-1-2014 用于加熱和.或冷卻的氣體的吸附裝置使用凈熱輸入不超過70千瓦.第1部分:術語和定義
• EN 12309-2-2015 燃氣吸附設備加熱和/或冷卻的凈熱量輸入不超過70千瓦.第2部分:安全性
• EN 12309-3-2014 用于加熱和.或冷卻的氣體的吸附裝置使用凈熱輸入不超過70千瓦.第3部分:測試條件
• EN 12309-4-2014 用于加熱和.或冷卻的氣體的吸附裝置使用凈熱輸入不超過70千瓦.第4部分:測試方法
• EN 12309-5-2014 用于加熱和.或冷卻的氣體的吸附裝置使用凈熱輸入不超過70千瓦.第5部分:必備要求
• EN 12309-6-2014 用于加熱和.或冷卻的氣體的吸附裝置使用凈熱輸入不超過70千瓦.第6部分:季節性能計算
• EN 14511-1-2013 
• EN 14511-2-2013 空間加熱和制冷用電動壓縮機空調,液體冷卻裝置及熱泵.第2部分:試驗條件
• EN 14511-3-2013 空間加熱和制冷用電動壓縮機空調,液體冷卻裝置及熱泵.第3部分:試驗方法
• EN 14511-4-2013 空間加熱和制冷用帶電驅動壓縮機的空調,液體冷卻包和熱泵.第4部分:操作要求,評分和指南
• EN 14825-2016 
• EN 16905-3-2017 燃氣吸熱發動機驅動熱泵.第3部分:試驗條件
• EN 16905-4-2017 燃氣發動機熱泵 -第4部分:試驗方法
• EN 16905-5-2017 燃氣吸熱發動機驅動熱泵.第5部分:加熱和冷卻模式季節性性能的計算

DIN EN 16905-1-2017的歷代版本如下：

• 2017年09月 DIN EN 16905-1-2017 燃氣式吸熱發動機驅動熱泵.第1部分:術語和定義;德文版本EN 16905-1-2017

非常抱歉，我們暫時無法提供預覽，您可以試試： 免費下載 DIN EN 16905-1-2017 前三頁，或者稍后再訪問。

注意： 點擊下載后，生成下載文件時間比較長，請耐心等待......

標準號

DIN EN 16905-1-2017

發布日期

2017年09月

實施日期

廢止日期

無

中國標準分類號

J75

國際標準分類號

01.040.27;27.080

發布單位

DE-DIN

引用標準

EN 161-2011 EN 437-2003 EN 12309-1-2014 EN 12309-2-2015 EN 12309-3-2014 EN 12309-4-2014 EN 12309-5-2014 EN 12309-6-2014 EN 14511-1-2013 EN 14511-2-2013 EN 14511-3-2013 EN 14511-4-2013 EN 14825-2016 prEN 16905-2 EN 16905-3-2017 EN 16905-4-2017 EN 16905-5-2017

被代替標準

DIN EN 16905-1-2015

適用范圍

This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This standard only applies to appliances having: - gas fired endothermic engines under the control of fully automatic control systems; - closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; - where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 during normal operation; - where the maximum operating pressure in the - heating water circuit (if installed) does not exceed 6 bar - domestic hot water circuit (if installed) does not exceed 10 bar. This standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this standard. Packaged units, single split and multisplit systems are covered by this standard. Single duct and double duct units are covered by this standard. The above appliances can have one or more primary or secondary functions. This standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested wo

DIN EN 16905-1-2017系列標準