ASTM E2231-15
評定表面燃燒特性用管道和導管絕緣材料的試樣制備和安裝的標準實施規程

Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

被代替

標準號

ASTM E2231-15

發布

2015年

發布單位

美國材料與試驗協會

替代標準

ASTM E2231-18

當前最新

ASTM E2231-21

 

 

引用標準

ASTM A390 ASTM C1136 ASTM C1224 ASTM C1396/C1396M ASTM C168 ASTM E176 ASTM E2599 ASTM E84 IEEE/ASTM SI 10

適用范圍

5.1 Pipe and duct insulation systems are often evaluated with Test Method E84 to comply with building or mechanical code requirements. This practice describes, in detail, specimen preparation and mounting procedures for single-component pipe or duct insulation systems and for multi-component pipe or duct insulation systems.

5.2 The material, system, composite, or assembly tested shall be representative of the completed insulation system used in actual field installations, in terms of the components, including their respective thicknesses.

5.3 Pipe and duct insulation systems consist of a variety of materials and constructions.

5.4 Some testing laboratories have developed a number of protocols for testing pipe or duct insulation systems which utilize one generic type of materials, all of them with an insulation core and a jacket. Those protocols are the origin of this practice, which makes them generic, to reduce material bias in the standard; they have resulted in the procedures presented in 6.1. The procedures presented in 6.2 – 6.5 address other types of pipe or duct insulation systems.

5.5 This practice addresses specimen preparation and mounting of systems of the types described in 5.5.1 – 5.5.3 and testing of supplementary materials as described in 5.6.

5.5.1 Multi-component systems containing an insulation core and a jacket, with or without adhesive between insulation core and jacket, not intended to be bonded to a pipe or duct substrate. Specimen preparation and mounting for such systems is described in 6.1 if they are self-supporting and in 6.2 if they are not self-supporting.

5.5.2 Single component systems, not intended to be bonded to a pipe or duct substrate. Specimen preparation and mounting for such systems is described in 6.3 if they are self-supporting and in 6.4 if they are not self-supporting.

5.5.3 Systems intended to be bonded to a pipe or duct substrate. Specimen preparation and mounting for such systems is described in 6.5.

5.5.4 Reflective insulation materials (see 3.2.10 and 3.2.11) intended to be used as pipe or duct insulation materials and installed with an air gap shall be tested using the procedures for specimen preparation and mounting procedures described in Practice E2599. Reflective insulation materials intended to be used as pipe or duct insulation materials and installed without an air gap shall b......

45°燃燒性測試實驗方法

一、主題內容與適用范圍　　本標準規定了服裝用紡織品易燃性的測定方法及評定服裝用紡織品易燃性的三種等級。　　本標準適用于測量易燃紡織品穿著時一旦點燃后燃燒的劇烈程度和速度。　　二、引用標準：GB 5457 紡織品及紡織制品的燃燒性能詞匯表　　三、術語　　3.1 絨面。指織物中具有各種絨頭的表面，如拉絨、起絨、簇絨、植絨或類似的表面。　　3.2 易燃性。...

FTT單體燃燒測試儀（SBI）

? “氣體控制箱”，安裝在測試箱觀察窗旁邊，以便操作人員可以同時查看測試試樣和丙烷流量(mg/s)。該裝置包括3個流量水平控制器、警示燈和過載設備。? “氣體分流器”包括質量流量控制器，用于控制丙烷氣體流量。兩個供氣管中的電磁閥和回火抑制器用于氣體流向燃燒器的自動安全操作。這些被放置在靠近測試框架的地方，通過減少電磁閥和燃燒器之間的管道長度來提高燃燒器的響應時間。...

ASTM D1230-1994 服裝紡織品可燃性的測試方法

引用標準2.1 ASTM標準：D123?與紡織；品有關的術語D484?烴類干洗溶劑的說明D2724?粘合、熔合和疊層服裝紡織物的測試方法E122?評定批或處理批量尺度用樣本大小的選擇2.2 AATCC?試驗方法AATCC 135?機織物和針織物在家用自動洗衣機中洗滌后尺寸的變化3.?術語3.1?定義：3.1.1?可燃紡織品—遭受外部火源時，可點燃并燃燒或可產生可點燃并燃燒的蒸汽。...

45°燃燒測試儀原理

b.氣體燃燒器，4 1/2號注射器針頭制成的。c. 計時器可自動計時，并準確到0.1s。2 刷毛裝置用于起絨或簇絨織物的試樣制備。由一個放置試樣夾的合適滑動架和垂直安裝于試樣表面上的負重尼龍毛刷構成。滑動架下裝四個輪子，可沿試樣前后方向移動，它的移動距離稍超過試樣暴露的長度。并裝有供滑動輪子移動的導軌。...

---

誰引用了ASTM E2231-15 更多引用

ASTM C1534-24 用作管道系統的隔熱和吸聲襯墊的柔性聚合物泡沫板絕緣材料的標準規范

---