ASTM E976-15
用于測定聲發射傳感器響應再現性的標準指南
Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response
ASTM E976-15 發布歷史
ASTM E976-15由美國材料與試驗協會 US-ASTM 發布于 2015。
ASTM E976-15 用于測定聲發射傳感器響應再現性的標準指南的最新版本是哪一版？
最新版本是 ASTM E976-15(2021) 。
ASTM E976-15 發布之時，引用了標準
- ASTM E2075 用丙烯酸桿檢驗AE傳感器響應一致性的標準實施規程
- ASTM E2374 聲發射系統性能驗證的標準指南
- ASTM E750 聲發射儀器特性表示
ASTM E976-15的歷代版本如下：
- 2021年 ASTM E976-15(2021) 測定聲發射傳感器響應再現性的標準指南
- 2015年 ASTM E976-15 用于測定聲發射傳感器響應再現性的標準指南
- 2010年 ASTM E976-10 聲發射傳感器響應再現性測定的標準指南
- 2005年 ASTM E976-05 測定聲發射傳感器響應再現性的標準指南
- 2000年 ASTM E976-00 聲音發射傳感器響應的再現性測定的標準指南
3.1 Acoustic emission data is affected by several characteristics of the instrumentation. The most obvious of these is the system sensitivity. Of all the parameters and components contributing to the sensitivity, the acoustic emission sensor is the one most subject to variation. This variation can be a result of damage or aging, or there can be variations between nominally identical sensors. To detect such variations, it is desirable to have a method for measuring the response of a sensor to an acoustic wave. Specific purposes for checking sensors include: (1) checking the stability of its response with time; (2) checking the sensor for possible damage after accident or abuse; (3) comparing a number of sensors for use in a multichannel system to ensure that their responses are adequately matched; and (4) checking the response after thermal cycling or exposure to a hostile environment. It is very important that the sensor characteristics be always measured with the same sensor cable length and impedance as well as the same preamplifier or equivalent. This guide presents several procedures for measuring sensor response. Some of these procedures require a minimum of special equipment.
3.2 It is not the intent of this guide to evaluate AE system performance. Refer to Practice E750 for characterizing acoustic instrumentation and refer to Guide E2374 for AE system performance verification.
3.3 The procedures given in this guide are designed to measure the response of an acoustic emission sensor to an arbitrary but repeatable acoustic wave. These procedures in no way constitute a calibration of the sensor. The absolute calibration of a sensor requires a complete knowledge of the characteristics of the acoustic wave exciting the sensor or a previously calibrated reference sensor. In either case, such a calibration is beyond the scope of this guide.
3.4 The fundamental requirement for comparing sensor responses is a source of repeatable acoustic waves. The characteristics of the wave do not need to be known as long as the wave can be reproduced at will. The sources and geometries given in this guide will produce primarily compressional waves. While the sensors will respond differently to different types of waves, changes in the response to one type of wave will imply changes in the responses to other types of waves.
3.5 These procedures use a test block or rod. Such a device provides a convenient mounting surface for the sensor and when appropriately marked, can ensure that the source and the sensor are always positioned identically with respect to each other. The device or rod also provides mechanical loading of the sensor similar to that experienced in actual use. Care must be taken when using these devices to minimize resonances so that the characteristics of the sensor are not masked by these resonances.
3.6 These procedures allow co......
點擊查看大圖
- 標準號
- ASTM E976-15
- 發布
- 2015年
- 發布單位
- 美國材料與試驗協會
- 替代標準
- ASTM E976-15(2021)
- 當前最新
- ASTM E976-15(2021)
- 引用標準
- ASTM E2075 ASTM E2374 ASTM E750