ASTM E1419/E1419M-15a
使用聲發射檢驗無縫充氣的壓力容器的標準實施規程
Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
ASTM E1419/E1419M-15a 發布歷史
ASTM E1419/E1419M-15a由美國材料與試驗協會 US-ASTM 發布于 2015。
ASTM E1419/E1419M-15a在國際標準分類中歸屬于: 23.020.30 壓力容器、氣瓶。
ASTM E1419/E1419M-15a 發布之時，引用了標準
- ASTM E1316 無損檢測標準術語
- ASTM E2075 用丙烯酸桿檢驗AE傳感器響應一致性的標準實施規程
- ASTM E2223 用角束超聲波檢查無縫充氣鋼制壓力容器的標準實施規程
- ASTM E2374 聲發射系統性能驗證的標準指南
- ASTM E543 無損檢測機構的標準實施規程
- ASTM E650 安裝壓電聲發射傳感器
- ASTM E976 測定聲發射傳感器響應再現性的標準指南
- ISO 16148 氣瓶.可重復充裝的無縫鋼氣瓶和管.定期檢驗和試驗用聲發射檢驗（AT）和后續超聲波檢驗（UT） -修正案1
- ISO 9712 無損檢測.無損檢測人員的資格和認證
ASTM E1419/E1419M-15a的歷代版本如下：
- 2020年 ASTM E1419/E1419M-15a(2020) 使用聲發射檢查無縫 充氣 壓力容器的標準實踐
- 2015年 ASTM E1419/E1419M-15a 使用聲發射檢驗無縫充氣的壓力容器的標準實施規程
- 2015年 ASTM E1419/E1419M-15 采用聲發射法檢驗無縫, 充氣壓力容器的標準實施規程
- 2009年 ASTM E1419-09 用聲音排放法檢驗無縫、充氣的壓力容器的標準試驗方法
- 2002年 ASTM E1419-02b 利用聲波發射檢驗充有氣體的無縫壓力容器的標準試驗方法
- 2002年 ASTM E1419-02a 利用聲波發射檢驗充有氣體的無縫壓力容器的標準試驗方法
- 2002年 ASTM E1419-02 利用聲波發射檢驗充有氣體的無縫壓力容器的標準試驗方法
- 2002年 ASTM E1419-00 用聲發射檢驗無縫充氣壓力容器的標準試驗方法
5.1 Because of safety considerations, regulatory agencies (for example, U.S. Department of Transportation) require periodic examinations of vessels used in transportation of industrial gases (see Section 49, Code of Federal Regulations). The AE examination has become accepted as an alternative to the common hydrostatic proof test. In the common hydrostatic test, volumetric expansion of vessels is measured.
5.2 An AE examination should not be performed for a period of one year after a common hydrostatic test. See Note 2.
Note 2: The Kaiser effect relates to decreased emission that is expected during a second pressurization. Common hydrostatic tests use a relatively high pressure (1678201;% of normal service pressure). (See Section 49, Code of Federal Regulations.) If an AE examination is performed too soon after such a pressurization, the AE results will be insensitive to a lower examination pressure (that is, the lower pressure that is associated with an AE examination).
5.3 Pressurization:
5.3.1 General practice in the gas industry is to use low pressurization rates. This practice promotes safety and reduces equipment investment. The AE examinations should be performed with pressurization rates that allow vessel deformation to be in equilibrium with the applied load. Typical current practice is to use rates that approximate 3.45 MPa/h [5008201;psi/h].
5.3.2 Gas compressors heat the pressurizing medium. After pressurization, vessel pressure may decay as gas temperature equilibrates with ambient conditions.
5.3.3 Emission from flaws is caused by flaw growth and secondary sources (for example, crack surface contact and contained mill scale). Secondary sources can produce emission throughout vessel pressurization.
5.3.4 When pressure within a vessel is low, and gas is the pressurizing medium, flow velocities are relatively high. Flowing gas (turbulence) and impact by entrained particles can produce measurable emission. Considering this, acquisition of AE data may commence at some pressure greater than starting pressure (for example, 1/3 of maximum examination pressure).
5.3.5 Maximum Test Pressure—Serious flaws usually produce more acoustic emission (that is, more events, events with higher peak amplitude) from secondary sources than from flaw growth. When vessels are pressurized, flaws produce emission at pressures less than normal fill pressure. A maximum examination pressure that is 108201;% greater than normal fill pressure allows measurement of emission from secondary sources in flaws and from flaw growth.
5.3.6 Pressurization Schedule—Pressurization should proceed at rates that do not produce noise from the pressurizing medium and that allow ...... ......
- 標準號
- ASTM E1419/E1419M-15a
- 發布
- 2015年
- 發布單位
- 美國材料與試驗協會
- 替代標準
- ASTM E1419/E1419M-15a(2020)
- 當前最新
- ASTM E1419/E1419M-15a(2020)
- 引用標準
- ANSI/ASNT CP-189 ASTM E1316 ASTM E2075 ASTM E2223 ASTM E2374 ASTM E543 ASTM E650 ASTM E976 ISO 16148 ISO 9712