CEN/TS 16637-2-2014
建筑產品.危險物質排放的評估.第2部分：水平動態表面浸取試驗

Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test

CEN/TS 16637-2-2014 發布歷史

(1) This Technical Specification specifies a Dynamic Surface Leaching Test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. (2) This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use may be established by means of modelling (not included in this Technical Specification). (3) The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. (4) The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions (volume > 64000 mm 3(64 cm 3 )). It also applies to plate- or sheet-like products with surface areas of minimum 10000 mm 2(100 cm 2 ) exposed to the leachant. Products designed to drain water (e. g. draining tiles, porous asphalt) and monolithic granular products according to CEN/TS 16637-1:2014, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. (5) Metals, metallic coatings and organic coatings on metals are excluded from the scope of CEN/TS 16637-2 because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. (6) For some coatings (e. g. some renders with organic binders according

CEN/TS 16637-2-2014由歐洲標準化委員會 IX-CEN 發布于 2014-08。

CEN/TS 16637-2-2014 在中國標準分類中歸屬于: Z60 污染物排放綜合，在國際標準分類中歸屬于: 13.040.20 環境空氣,19.040 環境試驗,91.100.01 建筑材料綜合。

CEN/TS 16637-2-2014 發布之時，引用了標準

• EN 14346-2006 廢棄物特征.通過測定干殘渣或水含量計算干物質含量*， 2022-07-28 更新
• CEN/TS 15863-2012 廢料的描述.浸出行為的測試基本的描述.與周期性leachant更新動態整體浸出試驗,在固定的測試條件
• CEN/TR 16045-2010 建筑產品-評估釋放有害物質管制的內容*， 2022-07-28 更新
• CEN/TR 16098-2010 建筑產品.危險物質的釋放評估.水平測試程序下的持續專業發展支持的要求概念*， 2022-07-28 更新
• EN 16192-2011 廢物特性描述.洗出液的分析*， 2022-07-28 更新
• CEN/TR 16496-2013 建筑產品.危險物質釋放的評估.協調的橫向評估方法的使用*， 2022-07-28 更新
• CEN/TS 16637-1-2014 建筑產品.危險物質排放的評估.第1部分：浸出試驗和附加試驗步驟的試驗指南
• EN ISO 3696-1995 分析實驗室用水.規范和試驗方法(ISO 3696-1987)
• EN ISO 5667-3-2012 水質采樣.第3部分:水樣的保存和處理*， 2022-07-28 更新

* 在 CEN/TS 16637-2-2014 發布之后有更新，請注意新發布標準的變化。

CEN/TS 16637-2-2014的歷代版本如下：

• 2014年08月 CEN/TS 16637-2-2014 建筑產品.危險物質排放的評估.第2部分：水平動態表面浸取試驗

非常抱歉，我們暫時無法提供預覽，您可以試試： 免費下載 CEN/TS 16637-2-2014 前三頁，或者稍后再訪問。

注意： 點擊下載后，生成下載文件時間比較長，請耐心等待......

標準號

CEN/TS 16637-2-2014

發布日期

2014年08月

實施日期

廢止日期

無

中國標準分類號

Z60

國際標準分類號

13.040.20;19.040;91.100.01

發布單位

IX-CEN

引用標準

EN 14346-2006 CEN/TS 15863-2012 CEN/TR 16045-2010 CEN/TR 16098-2010 EN 16192-2011 CEN/TR 16496-2013 CEN/TS 16637-1-2014 FprCEN/TS 16637-3 EN ISO 3696-1995 EN ISO 5667-3-2012 EA NEN 7375-2005

被代替標準

FprCEN/TS 16637-2-2013

適用范圍

(1) This Technical Specification specifies a Dynamic Surface Leaching Test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. (2) This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use may be established by means of modelling (not included in this Technical Specification). (3) The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. (4) The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions (volume > 64000 mm 3(64 cm 3 )). It also applies to plate- or sheet-like products with surface areas of minimum 10000 mm 2(100 cm 2 ) exposed to the leachant. Products designed to drain water (e. g. draining tiles, porous asphalt) and monolithic granular products according to CEN/TS 16637-1:2014, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. (5) Metals, metallic coatings and organic coatings on metals are excluded from the scope of CEN/TS 16637-2 because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. (6) For some coatings (e. g. some renders with organic binders according

誰引用了CEN/TS 16637-2-2014 更多引用