BS EN 777-1:2009
非家用多燃燒器的燃氣高架輻射管加熱器系統.第1部分:系統D.安全性
Multi-burner gas-fired overhead radiant tube heater systems for nondomestic use Part 1: System D — Safety
- 標準號
- BS EN 777-1:2009
- 發布
- 2009年
- 發布單位
- 英國標準學會
- 當前最新
- BS EN 777-1:2009
- 引用標準
- EN 10226-1:2004 EN 10226-2:2005 EN 126:2004 EN 161:2007 EN 257 EN 298:2003 EN 437:2003 EN 60335-1:2002 EN 60335-2-102:2006 EN 60529:1992 EN 60584-1:1995 EN 60584-2:1993 EN 88-1:2007 EN ISO 228-1:2003 EN ISO 6976:2005 ISO 70 ISO 7005-1:1992 ISO 7005-2:1988
- 被代替標準
- BS EN 777-1:1999
- 適用范圍
- This European Standard specifies the requirements and test methods for the construction, safety, classification and marking of non-domestic gas-fired overhead radiant tube heaters incorporated into a multi-burner system (called system D and referred to in the body of the text as the “system”) with each burner unit under the control of an automatic burner control system. This standard is applicable to Type B52 systems (see 4.3) intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means. This standard is not applicable to: a) systems designed for use in domestic dwelling; b) outdoor systems; c) systems of heat input in excess of 120 kW (based on the net calorific value of the appropriate reference test gas); d) systems having a draught diverter; e) systems having fully pre-mixed gas and air burners in which: 1) either the gas and all the combustion air are brought together just before the level of the combustion zone; or 2) the pre-mixing of the gas and all combustion air is carried out in a part of the burner upstream of the combustion zone; f) systems that are designed for continuous condensation within the flue system under normal operating conditions; g) systems having combustion products evacuation ducts that are non-metallic. This standard is applicable to systems which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals. NOTE Requirements for systems which are not intended to be type tested would need to be subject to further consideration. Requirements concerning the rational use of energy have not been included in this European Standard.
BS EN 777-1:2009相似標準
推薦
原子吸收分光光度計各個部分的作用
可消除光源不穩定性造成的誤差。可見，原子吸收分光光度計一般由光源，原子化器，單色器，檢測器等四部分組成。一、光源1．作用：提供待測元素的特征譜線——共振線。獲得較高的靈敏度和準確度。光源應滿足如下要求：①. 輻射的共振線半寬度明顯小于吸收線的半寬度---—銳線光源（Δν≤2×10-3nm）； ②. 共振輻射強度足夠大，以保證有足夠的信噪比； ③. 穩定性好，背景小 。...
實驗室光學儀器--原子吸收分光光度計的基本結構及功能
原子吸收分光光度計(原子吸收光譜分析儀)包括四大部分:光源、原子化系統、分光系統、檢測系統,如圖1-1所示。圖1-1 原子吸收分光光度計基本構造示意圖1、光源光源的作用是輻射待測元素的特征光譜(實際輻射的是共振線和其他非吸收譜線),以供測量用。為了獲得較高的靈敏度和準確度,所使用的光源必須滿足如下要求:(1)能輻射銳線,即發射線的半寬度要比吸收線的半寬度窄得多,否則測出的不是峰值吸收系數。...
原子吸收光譜法--AAS儀器篇
可以測定共振吸收線位于真空紫外區的非金屬元素I、P、S等。f.?石墨爐原子化法所用設備比較復雜，成本比較高。但石墨爐原子化器在工作中比火焰原子化系統安全。g.?石墨爐產生的總能量比火焰小，因此基體干擾較嚴?重，測量的精密度比火焰原子化法差。石墨爐的基本結構包括：石墨管（杯）、爐體（保護氣系統）、電源等三部分組成。工作是經歷干燥、灰化、原子化和凈化等四個階段，即完成一次分析過程。1.?...
這些國家標準已正式實施，涉及新能源、半導體、醫療器械
17713-20112024/1/16GB/T 42168.1-2022避孕套 臨床研究指南 第1部分：男用避孕套基于自我報告的臨床功能研究2024/1/17GB/T 42169-2022綠色產品評價 家用燃氣用具2024/1/18GB/T 9473-2022讀寫作業臺燈性能要求GB/T 9473-20172024/1/19GB/Z 42217-2022醫療器械 用于醫療器械質量體系軟件的確認2024...