ASTM D4327-2003
用化學壓縮離子色譜法對水中陰離子的標準試驗方法

Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography

標準號

ASTM D4327-2003

發布日期

2003年

實施日期

廢止日期

無

中國標準分類號

Z16

國際標準分類號

13.060.50 (Examination of water for chemical subst

發布單位

US-ASTM

適用范圍

Ion chromatography provides for both qualitative and quantitative determination of seven common anions, F^x2212;, Cl^x2212;, NO₂^x2212;, HPO₄^x2212;2, Br^x2212;, NO₃^x2212;, and SO₄^x2212;2, in the milligram per litre range from a single analytical operation requiring only a few millilitres of sample and taking approximately 10 to 15 min for completion.

Note 28212;This test method may be used to determine fluoride if its peak is in the water dip by adding one mL of eluent (at 100x00D7; the concentration in 8.3) to all 100-mL volumes of samples and standards to negate the effect of the water dip. (See 6.3, and also see 6.4.) The quantitation of unretained peaks should be avoided. Anions such as low molecular weight organic acids (formate, acetate, propionate, etc.) that are conductive coelute with fluoride and would bias fluoride quantitation in some drinking waters and most wastewaters.

Anion combinations such as Cl^x2212;/Br^x2212; and NO₂^x2212;/NO₃^x2212;, which may be difficult to distinguish by other analytical methods, are readily separated by ion chromatography.

1.1 This test method covers the sequential determination of fluoride, chloride, nitrite, ortho-phosphate, bromide, nitrate, and sulfate ions in water by chemically suppressed ion chromatography. Note 1Order of elution is dependent upon the column used; see .

1.2 This test method is applicable to drinking and wastewaters. The ranges tested for this test method for each anion were as follows (measured in mg/L):

	Fluoride	0.26 to 8.49
	Chloride	0.78 to 26.0
	Nitrite-N	0.36 to 12.0
	Bromide	0.63 to 21.0
	Nitrate-N	0.42 to 14.0
	o-Phosphate	0.69 to 23.1
	Sulfate	2.85 to 95.0

1.3 It is the user''s responsibility to ensure the validity of this test method for other matrices.

1.4 Concentrations as low as 0.01 mg/L were determined depending upon the anions to be quantitated, in single laboratory work. Utilizing a 50-956;L sample volume loop and a sensitivity of 3 956;S/cm full scale, the approximate detection limits shown in Table 1 can be achieved. If lower detection levels are required, the sensitivity may be improved by using a lower scale setting (< 3 956;S/cm) or a larger sample injection loop (>100 956;L). The analyst must assure optimum instrument performance to maintain a stable baseline at more sensitive conductivity full-scale settings.

1.5 The upper limit of this test method is dependent upon total anion concentration and may be determined experimentally as described in Annex A1. These limits may be extended by appropriate dilution or by use of a smaller injection volume.

1.6 Using alternate separator column and eluents may permit additional anions such as formate or citrate to be determined. This is not the subject of this test method.

1.7 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the appl......