• <li id="ccaac"></li>
  • <table id="ccaac"><rt id="ccaac"></rt></table>
  • <td id="ccaac"></td>
  • <td id="ccaac"></td>
  • BS EN 13476-2:2007
    無壓地下排水和污水塑料管系統.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)結構壁管系統.A型、有平滑內外表面的管和配件及系統用規范

    Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Specifications for pipes and fittings with smooth interna

    2018-06

    標準號
    BS EN 13476-2:2007
    發布
    2007年
    發布單位
    英國標準學會
    替代標準
    BS EN 13476-2:2018
    當前最新
    BS EN 13476-2:2018+A1:2020
     
     
    引用標準
    CEN/TS 14541-2007 EN EN 1053 EN 1055:1996 EN 12061 EN 12256 EN 12666-1 EN 1277 EN 13476-1:2007 EN 13476-3 EN 1401-1 EN 1411 EN 1437 EN 1446 EN 14741 EN 14758-1 EN 1852-1 EN 1905 EN 1979 EN 476 EN 580 EN 681-1 EN 681-2 EN 681-4 EN 727 EN 728 EN 744 EN 922
    被代替標準
    06/30082990 DC-2006
    適用范圍
    This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicable to: a) structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by “U”; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure (application area code “D”); reflected in the marking of products by “UD”. This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 For dimensions larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

    BS EN 13476-2:2007相似標準


    推薦

    管材耐壓試驗機的原理介紹

    管材打壓機(管材耐壓爆破試驗機)符合GB/T 6111標準, 適用于熱塑性塑料管材(給水管聚乙烯PE管材、建筑給水硬質聚氯乙烯PVC-U管材、冷熱水PP-R、PP-H、 PP-B管材、鋁復合壓力、農業低壓灌溉聚Z烯PE軟管、硬質聚氯乙烯管材的長期靜液壓強度試驗瞬時爆破壓力試驗。...

    環剛度試驗機適用材質標準

    《埋地聚乙烯PE結構管道系統 第1部分 聚乙烯波紋管材》8、HDPE纏繞結構檢測項目:環剛度...

    襯塑鋼管的選購使用

    給水襯復合鋼管是在鋼管內壁,按輸送介質的要求內襯乙烯(PE)、耐熱聚乙烯PE-RT)、交聯聚乙烯PE-X)、聚丙烯PP-R)、硬聚氯乙烯PVC-U)、氯化聚氯乙烯(PVC-C)等熱塑性塑料管制成。    由于工藝的改進,有些產品增加了外覆層。產品按輸送水的溫度分為冷水襯塑鋼管熱水襯塑鋼管。產品標記由襯塑鋼管代號、襯材料代號、公稱通徑組成。   ...

    塑料管壓扁平試驗機的使用說明

    2部分:聚乙稀雙波紋管材》GB/T16800-1997《排水芯層發泡硬聚氯乙烯PVC-U)管材》GB/T18477-2001《埋地排水聚氯乙烯PVC-U)雙波紋管材》GB/T21238-2008《玻璃纖維增強塑料夾砂》GB/T 165-2002 《高密度聚乙烯纏繞結構管材》GB/T 838-1998 《玻璃纖維纏繞增強熱固性樹脂夾砂壓力》GB/T16491、GB/T5836等標準的規定...





    Copyright ?2007-2022 ANTPEDIA, All Rights Reserved
    京ICP備07018254號 京公網安備1101085018 電信與信息服務業務經營許可證:京ICP證110310號

  • <li id="ccaac"></li>
  • <table id="ccaac"><rt id="ccaac"></rt></table>
  • <td id="ccaac"></td>
  • <td id="ccaac"></td>
  • 床戏视频