關鍵字：
板材, HPL,
人造裝飾板, EN
438-2, BS EN
438-4,
Artificial Decorative plates,
層壓板, BS EN 438-3, BS EN 438, GB/T 17657, 密度板測試, EN 622, 纖維板測試, 膠合板測試, 甲醛測試, SGS, GB/T 15102, AS 2269, ANSI NEMA LD 3, AS/NZS 2269, SGS廈門, 廈門SGS, 裝飾板檢測, 人造板測試
SGS專業實驗室提供人造裝飾板Artificial Decorative plates測試服務
針對Wood-based Panels 木基板材（歐盟EN標準）常規測試項目：彎曲強度Bending strength, 彎曲彈性模量Modulus of in bending, 膠合板剪切強度, 浸水后厚度膨脹率Swelling in thickness after immersion in water, 垂直板面抗拉強度Tensile strength perpendicular to the plane of the board, 含水率moisture content, 密度Density, 長度, 寬度和厚度Length, Width and thickness, 方正度和邊直度Squareness and Straightness
人造裝飾板Artificial Decorative plates相關產品規范：
EN 438-2:2005 High-pressure decorative laminates (HPL)-Sheets based on thermosetting resins (usually called Laminates)-Part 2: Determination of properties
裝飾用高壓層壓制件(HPL).熱固性樹脂為基質的板材.第2部分:性能測試
Assessment of appearance外觀評價, Determination of thickness厚度, Determination of length and width長寬, Determination of edge straightness邊直線度, Determination of edge squareness邊直角度, Resistance to surface wear表面耐磨測試, Resistance to abrasion耐磨測試, Resistance to Immersion in Boiling Water耐沸水浸泡, Substrate protection against water vapour基材耐水蒸汽保護, Resistance to water vapour耐水蒸汽, Resistance to wet conditions耐濕測試, Resistance to dry heat耐干熱, Dimensional stability at elevated temperature高溫尺寸穩定性, Resistance to climatic shock耐環境溫濕變化測試, Resistance to impact by small-diameter ball耐小球沖擊, Resistance to impact by large-diameter ball耐大球沖擊, Resistance to impact by large-diameter ball耐大球沖擊, Resistance to cracking under stress耐應力開裂(層壓板厚度≤2mm), Resistance to crazing (Compact laminates) 耐龜裂, Resistance to scratching 耐刮痕, Resistance to staining 耐污性, Light resistance(Xenon arc)耐光色牢度(氙弧燈), Resistance to UV light (Exterior grade laminates)耐紫外光(適于外用級層壓板), Resistance to artificial weathering(including light fastness)耐人工氣候老化(包括光照色牢度), Resistance to cigarette burns耐香煙燃燒, Formability(Method A)可成型性(方法A), Resistance to blistering(Method A)耐起泡(方法A)
EN 438-6:2005 High-pressure decorative laminates (HPL)-Sheets based on thermosetting resins (usually called Laminates)- Part 6: Classification and specifications for Exterior-grade Compact laminates of thickness 2 mm and greater
EN 438-6:2005 裝飾用高壓層壓制件(HPL).熱固性樹脂為基質的板材.第6部分:等于和大于2mm厚的外部用壓實層壓板材的分類和規范
Flexural modulus彎曲模量, Flexural strength彎曲強度, Tensile strength拉伸強度, Density密度, Resistance to impact by large diameter ball（shatter resistance)耐落球(大直徑落球)沖擊測試, Resistance to wet conditions耐濕測試, Dimensional stability at elevated temperature 高溫尺寸穩定性, Resistance to climatic shock耐環境溫濕變化測試, Resistance to UV light (Exterior grade laminates)耐紫外光（適于外用級層壓板）, Resistance to artificial weathering(including light fastness)耐人工氣候老化(包括光照色牢度), Requirement for reaction to fire防火性能要求
BS EN 438-4:2005 High-pressure decorative laminates(HPL) — Sheets based on thermosetting resins (Usually called Laminates) —Part 4: Classification and specifications for Compact laminates of thickness 2 mm and greater
裝飾用高壓層壓制件(HPL).基于熱固性樹脂的薄板材(通常稱為層壓制件).第4部分:厚度為2毫米和大于2毫米的壓實層壓制件的分類和規范
Inspection requirements 外觀檢查, Determination of thickness厚度, Determination of length and width長寬, Determination of edge straightness邊直線度, Determination of edge squareness邊直角度, Determination of flatness平整度, Resistance to surface wear表面耐磨性能, Resistance to impact by largediameter ball (optional)耐落球(大直徑)沖擊, Resistance to scratching耐刮擦, Resistance to dry heat 耐高溫干熱(180°C), Resistance to wet heat (100°C)耐高溫濕熱, Resistance to staining耐污染, Light fastness (xenon arc)耐光性能, Resistance to water vapour耐水蒸氣, Resistance to cigarette burns 耐香煙燃燒, Resistance to crazing耐龜裂, Flexural modulus /Flexural Strenth 彎曲模量/彎曲強度, Tensile strength 拉伸強度, Density密度, Reaction to fire防火性能, Spread of flame火焰傳播
其它產品規范如：
BS EN 438-3:2005 High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins (Usually called laminates) —Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
裝飾用高壓層壓制件(HPL).基于熱固性樹脂的薄板材(通常稱為層壓制件).第3部分:用于粘結支撐基質的不足2毫米厚的層壓制件的分類和規范
GB/T 17657-2013 人造板及飾面板理化性能試驗方法
Test methods of evaluating the properties of wood-based panels and surface decorated wood-based panels
AS 6669 Plywood-formwork
膠合板-模板
AS 2269.0 Plywood-Structure Part.0 specifications
膠合板-結構 第0部分：規范
AS/NZS 2269.1:2012 Plywood-Structure Part.1 Test methods
膠合板—結構 第1部分：測試方法
ANSI NEMA LD 3-2005 High-Pressure Decorative Laminates
高壓裝飾層壓板
GB/T 15102-2006 浸漬膠膜紙飾面人造板
Surface decorated wood-based panels with paper impregnated thermosetting resins
EN 622-1:2003 Fibreboards - Specifications - Part 1: General requirements
纖維板—規范—第一部分：一般要求
EN 622-2 Fibreboards - Specifications - Part 2: Requirements for hardboards
纖維板—規范—第二部分：硬木板的要求
EN 622-3 Fibreboards - Specifications - Part 3: Requirements for medium boards
纖維板—規范—第三部分：中密度板的要求
SGS提供的服務非常廣泛，包括檢驗、測試、產品認證、工廠審核、體系認證、貿易保障等。若您所檢測項目或其他認證、檢驗等服務沒有在列在上面，請和我們聯系咨詢，我們可根據標準或客戶要求，提供相關服務。
詳情請垂詢：
SGS通標標準技術服務有限公司
福建省廈門市火炬（翔安）產業區翔虹路31號
郭女士（Nicky Guo）
聯系電話（Tel）：+86-0592-5766954(直線)
移動電話（Mobile)：18650803319
郵箱E-Mail：
Nicky.guo@sgs.com
關于SGS
SGS 是全球領先的檢驗、鑒定、測試和認證機構。 我們是全球公認的質量和誠信基準。 80,000多名員工在全球運作1,650 多個分支機構和實驗室。
