共找到 150 條與 T型空心錐柄 相關的標準，共 10 頁
Hollow taper shank of tools (HSK). Types T. Basic dimensions
Tool receiver for type T hollow taper shanks (HSK). Connecting dimensions
GB/T 19449的本部分規定了適用于機床(如:車床、車銑床)的帶有法蘭接觸面的空心工具柄(HSK)的尺寸。本部分規定的T型柄,法蘭上帶有一個環形槽用于自動換刀,這種工具同樣可以通過錐柄上孔進行手動換刀。扭矩的傳遞是通過錐柄尾端的鍵以及摩擦來完成
Hollow taper interface with flange contact surface.Part 3:Dimensions of shanks for stationary tools
GB/T19449 的本部分規定了適用于機床(如:車床.車銑床)的帶有法蘭接觸面的空心工具柄安裝孔的尺寸。 與之配套的空心工具柄的尺寸在GB/T19449 的第3 部分規定。 本部分規定的T型安裝孔,用于自動換刀和手動夾緊。 手動夾緊是通過安裝孔上孔和柄上的孔來實現。 扭矩的傳遞是通過錐柄尾端的鍵
Hollow taper interface with flange contact surface.Part 4:Dimensions of receivers for stationary tools
本文件規定了用于機床（車床及車銑復合機床）的空心錐柄（HSK）的錐面和法蘭接觸面的接收器尺寸，根據ISO 12164-3。 本文件規定了兩種類型的接收器： — 類型T用于自動換刀； — 類型U僅用于手動換刀，通過接收器和工具柄中的徑向孔。 注1：類型T和U的接收器適用于HSK柄T、TA和U（根據
Hollow taper interface with flange contact surface. Receivers of types T and U for hollow taper shanks of types T, TA and U
This document specifies dimensions for receivers with taper and flange contact surfaces for hollow taper shanks (HSK) according to ISO?12164-3
Hollow taper interface with flange contact surface - Part 4 : receivers of types T and U for hollow taper shanks of types T, TA and U
Hollow taper interface with flange contact surface - Part 4 : receivers of types T and U for hollow taper shanks of types T, TA and U
This document specifies dimensions for receivers with taper and flange contact surfaces for hollow taper shanks (HSK) according to ISO 12164-3
Hollow taper interface with flange contact surface — Part 4: Receivers of types T and U for hollow taper shanks of types T, TA and U
Hollow taper shanks with flat contact surface - Part 5: Hollow taper shanks type E; Dimensions and design
Hollow taper interface with flange contact surface — Part 4: Receivers of types T and U for hollow taper shanks of types T, TA and U
Hollow taper shanks with flange contact surface - Part 2: Hollow taper shank type B; Dimensions and design / Note: To be replaced by DIN 69893-2 (2013-11).
BS ISO 12164-4. Hollow taper interface with flange contact surface - Part 4: Receivers of type T and U for hollow taper shanks of type T, TA and U
本文件規定了帶法蘭接觸面的空心錐柄（HSK）的尺寸。這些錐柄是與機床（如銑/鉆、車削和磨床）接口的陽部分。本文件規定了三種類型的錐柄： - 類型T具有用于車床自動換刀的周邊凹槽法蘭，帶有HSK類型T的夾持器； - 類型TA具有用于銑床自動換刀的周邊凹槽法蘭，設計用于車削，帶有HSK類型A或AB的夾持
Hollow taper interface with flange contact surface. Shanks of types T, TA and U
The document specifies the dimensions for hollow taper shanks with flat contact surface which can be used on high speed work spindles machine tools
Hollow taper shanks with flat contact surface - Part 5: Hollow taper shanks type E; Dimensions
Hollow taper shanks with flat contact surface - Part 5: Hollow taper shanks type E - Dimensions and design
