共找到 150 條與 起始溫度 相關的標準，共 10 頁
本標準規定了在線性加熱速率條件下使用差示掃描量熱法或壓力差示掃描量熱法測試碳氫化合物氧化放熱性質的測定方法。本標準適用于碳氫化合物的氧化起始溫度的測定
Determination of oxidative onset temperature of hydrocarbons by differential.Scanning calorimetry
E2009-Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
5.1 Oxidation onset temperature is a relative measure of the degree of oxidative stability
Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
1.1 These test methods describe the determination of the oxidative properties of hydrocarbons by differential scanning calorimetry or pressure
Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
本指南提供了根據DIN EN 760標準測定焊接粉末的燃燒起始溫度和平均燃燒值的方法，適用于使用實芯焊絲進行未預熱或低合金鋼焊接的情況
Determining the ignition temperature limits of UP welding powders during welding with solid-wire electrodes for unheated and low-alloy steels
Oxidation onset temperature is a relative measure of the degree of oxidative stability of the material evaluated at a given heating rate
Standard Test Method for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
1.1 This test method covers the procedure for determining the oxidative properties of hydrocarbons by differential scanning calorimetry or pressure
Standard Test Method for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
Paints and varnishes - Determination of polymerization characteristics by a method using a damped pendulum - Part 1: start temperature of polymerization reaction
Cross References: ISO 1513 ISO 1514 ISO 2808 ISO 4618 ISO 15528 IEC 60469-1:1987
BS ISO 12013-1. Paints and varnishes. Determination of curing characteristics using a free-damped oscillation method. Part 1. Start temperature of reaction
Test method for initial thermal decomposition temperature and deflagration temperature of composite solid propellant
本標準包括了純液體蒸汽壓力、混合物的蒸汽壓力（在一封閉管中，填充量為40%±5%時）及純液體和混合液體的初始熱分解溫度的測定。本標準適用于測試溫度下，在硼硅酸鹽瓶中其蒸汽壓在133Pa～101.3kPa間的液體蒸汽壓的測定。 本測試方法溫度適用范圍為環境溫度至748K。如提供合適的恒溫浴時，溫度
Test method for vapor pressure-temperature relationship and initial decompostition temperature of liquids by isoteniscope
本標準規定了溫濕度儀檢定箱的產品組成與功能、技術要求、試驗方法、檢驗規則、標志和隨行文件、包裝、運輸與貯存等。 本標準適用于氣象用溫濕度儀檢定箱的設計、生產、使用、檢驗和驗收
Temperature and humidity meter calibration box
本文件規定了光功率分析法測試薄膜材料相變溫度的術語和定義、原理、儀器和試劑、樣品處理、儀器校準、測試過程、數據處理、不確定度評定和測試報告等。 本文件適用于厚度為5 nm~100 μm的薄膜材料相變溫度的測試，薄膜材料應相變前后光反射率不同且在測試溫區內受熱不分解、不揮發。厚度
Phase transition temperature measurement of micro-nano thin film -Optical power analysis
本標準規定了差熱-熱重分析法測定煙火藥劑著火溫度的方法及安全技術規定。 本標準適用于煙火藥劑著火溫度的測定
Determination of ignition temperature of pyrotechnic composition-DTA-TG analysis
GB/T 5169的本部分詳細規定了在固體電氣絕緣材料或其他固體材料試驗樣品上進行起燃性試驗的灼熱絲試驗方法,目的是測定灼熱絲起燃溫度(GWIT)。本試驗方法是在一系列標準試樣上進行的材料試驗。其獲得的數據連同由IEC 60695-2-12材料灼熱絲可燃性指數(GWFI)試驗方法獲得的數據一起,按照
Fire hazard testing for electric and electronic product.Part 13:Glowing/hot-wire based test methods.Glow-wire ignition temperature (GWIT) test method for materials
