共找到 150 條與 保護導體端子 相關的標準，共 10 頁
Terminals for protective conductors in low-voltage switchgear and control gear
Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
BILINGUAL
Low-voltage switchgear and controlgear Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
This part of IEC 60947 specifies requirements for protective conductor terminal blocks with PE function up to 120 mm2 (250 kcmil) and for protective
Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
Draft Document - Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors (IEC 17B/1568/CDV:2007); German version EN 60947-7-2:2002/prA1:2007
Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment; Protective conductor terminal blocks for copper conductors (IEC 60947-7-2:2002); German version EN 60947-7-2:2002
Preface This is the harmonized ANCE, CSA Group, and UL standard for Low-Voltage Switchgear and Controlgear - Part 7-2: Ancillary Equipment
Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors (Trinational standard with NMX-J-538/7-2-ANCE and UL 60947-7-2)
GB14048 的本部分規定了主要用于工業的螺紋型或非螺紋型夾緊件的保護導體接線端子排的要求,具有PE保護功能的接線端子排不大于120 mm2 (250kcmi
Low-voltage switchgear and controlgear.Part 7-2:Ancillary equipment.Protective conductor terminal blocks for copper conductors
本標準規定了主要用于工業用的帶螺紋型或非螺紋型夾緊件的保護導體接線端子排，具有PE保護功能的接線端子排不大于120mm2（250MCM），具有PEN保護功能的接線端子排大于或等于10mm2（AWG8）。 保護導體接線端子排用于銅導體和安裝支架之間的電氣和機械連接
Low-voltage switchgear and controlgear. Ancillary equipment. Section 2: Protective conductor terminal blocks for copper conductors
系列標準《建筑物電氣裝置》的本部分對接地配置、保護導體和保護聯結導體作出了相應的規定，以便滿足電氣裝置安全方面的要求
Electrical installations of buildings--Part 5-54:Selection and erection of electrical equipment-Earthing arrangements,protective conductors and protective bonding conductors
本文件規定了主要用于工業或類似用途的PCB接線端子排的要求。通過釬焊、壓入或等效方式將銅導體安裝或固定在印制電路板上,從而使兩者之間形成電氣或機械連接。 本文件適用于額定電壓交流不超過1000V、頻率至1000 Hz或直流不超過1500V的電路中,用于連接截面積為0.08mm2 ~300mm2
Low-voltage switchgear and controlgear—Part 7-4: Ancillary equipment—PCB terminal blocks for copper conductors
本標準適用于如電阻、熔斷器、繼電器、導體、變壓器、旋轉機械及類似電氣設備組合的端子的標識與標志a 本標準也適用于某些特定導體的端子標識a 本標準還包括了字母數字系統的一般規則
Basic and safety principles for man-machine interface,marking and identification.Identification of equipment terminals and conductor terminations
Schválení ST SEV 2308-80 doporu?ilo federální ministerstvo hutnictví a tě?kého strojírenství. Zpracovatel a oborové normaliza?ní st?edisko: ZSE — V
Electric-engineering rules. Terminals for protective conductors on electric devices
各種工業生產中設備、測量、監視和控制用計算機的安全要求 規定了防電擊和電灼傷、防機械危險、防火焰蔓延、防過高溫影響的安全要求。也規定了通過檢查和型式試驗來鑒定設備是否符合要求的方法。適用于各種工業生產中的計算機產品。不包括功能、性能、運輸包裝有效性、電磁兼容性、爆炸環境防護措施、維修和維修人員防護等
Industrial control computer system—General specification—Part 2:Safety requirements for industrial control computer
