S11 線路構件 標準查詢與下載

GB/T 37330-2019 有砟軌道軌枕 混凝土枕

Sleeper for ballasted track—Concrete sleeper

GB/T 17955-2000 球型支座技術條件

本標準規定了球型支座的產品規格、分類與命名、技術要求、試驗方法、檢驗規則及標志、包裝、運輸和貯存。 本標準適用于支座承載力1 500～30 000kN的橋梁及其他工程結構所用的球型支座。

Technical requirements for spherical bearings

GB/T 9221-1988 防腐木枕

本標準規定了防腐木枕的技術條件、檢驗方法、檢驗規則和標志等內容。 本標準適用于標準軌距（1435mm）鐵路的普通木枕、木岔枕（道岔用木枕）和橋枕（橋梁用木枕）。

Preservatively-treated sleeper

TB/T 3570-2021 彈條Ⅲ型扣件

Spring type III fastener

BS EN 14730-2:2021 鐵路應用 追蹤 鋼軌的鋁熱焊 鋁熱焊工資格、承包商批準和焊縫驗收

This standard applies to aluminothermic welds made on Vignole rails of 46 kg/m and above as contained in EN 13674-1: This standard specifies: ? the system for training, testing and maintaining the skills of aluminothermic welders. It applies to those aluminothermic welding processes compliant with the requirements of EN 14730-1 "Railway applications – Track – Aluminothermic welding of rails – Part 1: Approval of welding processes". It requires that the system for training and testing of welders shall be approved by the relevant railway authority; ? the systems and requirements for the approval of aluminothermic welding contractors. It applies to those contractors using aluminothermic welding processes compliant with the requirements of EN 14730-1 "Railway applications – Track – Aluminothermic welding of rails – Part 1: Approval of welding processes" and who employ welders who are in possession of a valid Permit to Weld as defined in Clause 4 of this standard; ? the acceptance requirements for aluminothermic welds. It requires that weld inspectors are competent in aluminothermic weld inspection and are approved by the relevant railway authority. It covers the final inspection of aluminothermic welds for acceptance in track. It does not cover any previous inspections by welders or others.

Railway applications. Track. Aluminothermic welding of rails. Qualification of aluminothermic welders, approval of contractors and acceptance of welds

DIN EN 13848-6:2021 軌道交通. 軌道. 軌道幾何質量. 第6部分: 軌道幾何質量特性; 德文版本EN 13848-6-2014+A1-2020

This European Standard specifies the minimum requirements for track geometry measuring principles and systems in order to produce comparable results when measuring the same track. It applies to all measuring systems, attended or unattended, fitted on any vehicle, except track con

Railway applications - Track - Track geometry quality - Part 6: Characterisation of track geometry quality; German version EN 13848-6:2014+A1:2020

NF F58-020-1*NF EN 15746-1:2020 軌道交通. 鋼軌. 公路鐵路兩用機器及相關設備. 第1部分: 運行和作業的技術要求

Railway applications - Track - Road-rail machines and associated equipment - Part 1 : technical requirements for travelling and working

NF F58-600-6*NF EN 13848-6+A1:2020 軌道交通. 軌道. 軌道幾何質量. 第6部分: 軌道幾何質量特性

Domaine d'applicationCette Norme européenne caractérise la qualité de la géométrie des voies sur la base des paramètres définis dans l'EN 13848-1 et spécifie les différentes classes de géométrie de voie ! qu'il convient de considérer\

Railway applications - Track - Track geometry quality - Part 6 : characterisation of track geometry quality

BS EN 13848-2:2020 軌道交通. 軌道. 軌道幾何質量. 測量系統. 軌道檢查記錄車

Railway applications. Track. Track geometry quality. Measuring systems. Track recording vehicles

NF F58-600-2*NF EN 13848-2:2020 軌道交通. 軌道. 軌道幾何質量. 第2部分: 測量系統. 軌道檢查記錄車

Le présent document spécifie les exigences minimales pour les principes de mesure de la géométrie de la voie et pour les systèmes de mesure de la géométrie de la voie dans le but de produire des résultats comparables lors de mesures sur une même voie. Il s'applique à l'ensemble d

Railway applications - Track - Track geometry quality - Part 2 : measuring systems - Track recording vehicles

BS EN 13146-9:2020 軌道交通.軌道.緊固系統的試驗方法.剛度測定

Railway applications. Track. Test methods for fastening systems. Determination of stiffness

BS EN 13146-4:2020 軌道交通.軌道.緊固系統的試驗方法.重復負載的影響

This Part of this European Standard specifies a laboratory test procedure for applying repeated displacement cycles representative of the displacements caused by traffic on railway track. It is used for assessing the long term performance of direct fastening systems. This test procedure applies to a complete fastening assembly.

Railway applications - Track - Test methods for fastening systems - Effect of repeated loading

TB/T 3065-2020 彈條Ⅱ型扣件

本標準規定了彈條I型扣件彈條的技術要求、試驗方法、檢驗規則、包裝與標志。 本標準適用于彈條I型扣件彈條。

Spring clip-Ⅱ fastenings Part 2:Spring clip

TB/T 1495-2020 彈條Ⅰ型扣件

Spring type I fastener

TB/T 1911-2020 彈條Ⅰ型調高扣件

Elastic bar type I height-adjusting fastener

BS EN 13146-7:2019 鐵路應用程序 追蹤 緊固系統的測試方法 夾緊力和抗拔剛度的測定

This Part of this European Standard specifies laboratory test procedures for measuring the clamping force exerted by the fastening system on the foot of a rail. It is applicable to systems with and without baseplates on all types of sleepers, bearers and elements of slab track. These test procedures apply to a complete fastening assembly. A reference procedure and an alternative procedure are included.

Railway applications. Track. Test methods for fastening systems. Determination of clamping force and uplift stiffness

BS EN 14587-1:2018 鐵路應用 基礎設施 新鋼軌的閃光對焊 固定工廠內的 R220、R260、R260Mn、R320Cr、R350HT、R350LHT、R370CrHT 和 R400HT 級鋼軌

This European Standard specifies requirements for the approval of a welding process in a fixed plant, together with the requirements for subsequent welding production. It applies to new Vignole railway rails R220, R260, R260Mn and R350HT grade rails of 46 kg/m and above, as contained in EN 13674-1, welded by flash butt welding in a fixed plant and intended for use on railway infrastructure. This European Standard applies to the welding of rails into welded strings.

Railway applications. Infrastructure. Flash butt welding of new rails. R220, R260, R260Mn, R320Cr, R350HT, R350LHT, R370CrHT and R400HT grade rails in a fixed plant

JIS E 1305:2018 鐵路轉轍器.形狀及尺寸

Railway switches -- Shape and dimension

BS EN 13146-5:2012(2017) 軌道交通.軌道.緊固系統的試驗方法.重復負載的影響

This Part of this European Standard specifies a laboratory test procedure for applying repeated displacement cycles representative of the displacements caused by traffic on railway track. It is used for assessing the long term performance of direct fastening systems. This test procedure applies to a complete fastening assembly.

Railway applications - Track - Test methods for fastening systems - Effect of repeated loading

BS EN 13848-5:2017 鐵路應用 追蹤 跟蹤幾何質量 幾何質量水平 平線、道岔和交叉路口

Railway applications. Track. Track geometry quality. Geometric quality levels. Plain line, switches and crossings